| 上一篇主題 :: 下一篇主題 |
| 發表人 |
內容 |
mask
註冊時間: 2008-03-02
文章: 35
|
 發表於: 星期二 三月 11, 2008 6:13 am 文章主題: ????????? ???? for 4020 non-pressure filter |
 |
|
????????? ???? for 4020 non-pressure filter
? always ?? , ??????, ????????? |
|
| 回頂端 |
|
 |
wilsonc
註冊時間: 2007-09-23
文章: 65
|
| 發表於: 星期二 三月 11, 2008 9:51 am 文章主題: |
|
|
| ?????????? |
|
| 回頂端 |
|
|
mask
註冊時間: 2008-03-02
文章: 35
|
| 發表於: 星期二 三月 11, 2008 10:56 am 文章主題: |
|
|
| ??, ?????? filter ????? |
|
| 回頂端 |
|
|
???
註冊時間: 2006-03-11
文章: 829
|
| 發表於: 星期二 三月 11, 2008 1:38 pm 文章主題: |
|
|
???
???????
_________________
??????
???????
没?????
??????????? |
|
| 回頂端 |
|
|
mask
註冊時間: 2008-03-02
文章: 35
|
| 發表於: 星期二 三月 11, 2008 2:04 pm 文章主題: |
|
|
????? post ??canton road ???
thank you everybody |
|
| 回頂端 |
|
|
bib
註冊時間: 2007-04-21
文章: 786
|
| 發表於: 星期二 三月 11, 2008 4:25 pm 文章主題: |
|
|
| mask 寫到: | ????? post ??canton road ???
thank you everybody |
Sorry which post ?
Please help to relist the link.
Thanks |
|
| 回頂端 |
|
|
mask
註冊時間: 2008-03-02
文章: 35
|
|
| 回頂端 |
|
|
bib
註冊時間: 2007-04-21
文章: 786
|
| 發表於: 星期三 三月 12, 2008 1:18 am 文章主題: |
|
|
Hello mask,
Thank you very very much.
I want to see see there has some other gaskets I need.
BTW, I want to know some folks who has been there: Are they provide food grade gaskets ?
or just heat resistant gaskets only.
Since many gaskets not for EAT.
THANK YOU ar.
***Some more warmly remind :
TAI WOK la this time !!!
I call the shop, they told me they sell Industrial grade gaskets ONLY.
(((NON food GRADE))) !!! So, PLEASE be careful to take your own risk to put the gasket on.
THANK YOU.
bib 在 星期四 三月 13, 2008 7:59 am 作了第 1 次修改 |
|
| 回頂端 |
|
|
bib
註冊時間: 2007-04-21
文章: 786
|
| 發表於: 星期四 三月 13, 2008 7:56 am 文章主題: |
|
|
Some more information :
Please post the dimension of the gasket.
4020 Users need Viton gaskets !!
Need to find find la. Difficult to find !!
Viton is quite expensive, no many people keep stock.
I guess the best solution is ask * gor to find some vendor to make Viton thicker food grade gasket for 4020. Like the steam wand before...
Or if the rim does a matter , Can it be grinded off to make it flat ??
Hope can help.
. |
|
| 回頂端 |
|
|
kckc
註冊時間: 2006-03-15
文章: 1918
|
| 發表於: 星期日 三月 16, 2008 6:15 am 文章主題: |
|
|
yes it is this one, go and buy one.
it is not a concern coz the gasket will not get in contact with the water nor coffee in practical use
_________________
Eureka Mignon Hahaha |
|
| 回頂端 |
|
|
shing
Site Admin
註冊時間: 2006-03-01
文章: 1100
|
|
| 回頂端 |
|
|
bib
註冊時間: 2007-04-21
文章: 786
|
| 發表於: 星期一 三月 17, 2008 11:58 am 文章主題: |
|
|
| shing 寫到: | | dont confuse ar, the ground coffee cant touch the gasket gar. the gasket is outside the basket ar. |
Thanks for remind. Thank you thank you.
I found a better solution, may be cheaper.
Any where sells SHIM paper for the gasket ?
Remove the gasket and add the 0.75mm ? Please advice SHIM paper on the gasket, put it back...
Check 3M product.
Thanks |
|
| 回頂端 |
|
|
|
常見問題
搜尋
會員列表
會員群組
會員註冊
個人資料
登入檢查您的私人訊息
登入
